Inertial Labs IMU-P
$ 0,00
Advanced MEMS gyroscopes and accelerometers based IMU, developed and produce by Inertial Labs.
Lower cost alternative solution to expensive tactical-grade FOG gyroscopes based IMU (for example KVH DSP-3000 gyros based) and expensive MEMS IMUs (like Honeywell HG4930 etc.)
Drop in replacement version with Sensonor STIM300 Firmware is available.
Description
- 1 deg/hr Gyro Bias in-run stability
- 0.08 deg/√hr Angular Random Walk
- ±40 g accelerometers dynamic range
- 5 μg Accelerometers Bias in-run stability
- 0.015 m/s/√hr Velocity Random Walk
- 0.05 deg Pitch & Roll accuracy
- ITAR free (ECCN 7A994 – No License Required)
- Designed for stabilization (S) and guidance (A)
- Affordable price
Additional information
| Year of last update | 2018 |
|---|---|
| Alignment Error [ ± ° ] | 0.008 |
| Pitch and Roll static accuracy [ ° ] | 0.05 |
| Pitch and Roll dynamic accuracy [ ° ] | 0.08 |
| Num. of Gyroscopes | 3 |
| Range [± ° / sec] | 950 |
| In-Run Bias Stability [ °/ hr] | 1 |
| Bandwidth [ Hz ] | 260 |
| Non-linearity [ % ] | 0.05 |
| Noise | 0.025 |
| Pressure sensor | N |
| Output data formats | Binary, ASCII characters |
| Distinguishable features | • ITAR-free• Same mechanical & electrical interfaces as STIM-300• Affordable price• 1 deg/hr gyroscopes Bias in-run stability• 0.005 mg accelerometers Bias in-run stability• 0.004 deg/sec√Hz gyroscopes noise (PSD)• 0.025 mg√Hz accelerometers noise (PSD)• Advanced, extendable, embedded Kalman Filter• Full temperature calibration of all sensing elements• Up to 800Hz data rate• Environmentally sealed (IP67) |
| Application | • Antenna and Line of Sight Stabilization Systems• Passengers trains acceleration, deceleration and jerking systems• Motion Reference Units (MRU)• Motion Control Sensors (MCS)• Gimbals, EOC/IR, platforms orientation and stabilization• GPS-Aided Inertial Navigation Systems (INS)• Attitude and Heading Reference Systems (AHRS)• Land vehicles navigation and motion analysis• Buoy or Racing Boat Motion Monitoring• UAV & AUV/ROV navigation and control |
| Num. of Accelerometers | 3 |
| Range [max g] | 40 |
| Resolution [mg] | 0.001 |
| In-Run Bias Stability [mg] | 0.005 |
| Brand | Inertial Labs |
| Addres | Inertial Labs 39959 Catoctin Ridge Street 20129 Paeonian Springs United States |
| Output frequency [ Hz ] | 2000 |
| Start up time [s] | 1 |
| Year of initial development | 2015 |
| Non-operating shock tolerance [g] | 3000 |
| System components | Accelerometer(s), Gyroscope(s), Temperature sensor |
| Height [mm] | 22 |
| Width [mm] | 39 |
| Length [mm] | 45 |
| Weight [gr] | 70 |
| Min. Voltage (DC) | 30 |
| Max. Voltage (DC) | 5 |
| Power consumption [W] | 0.8 |
| Operating shock tolerance [g] | 1500 |
| Other interfaces and additional information | RS-232 as well, Same electrical & mechanical interface as Sensonor STIM-300 IMU |
| Min. operating temperature [C] | -40 |
| Max. operating temperature [C] | 85 |
| Splashproof casting | Y |
| Water resistant casting | Y |
| Water resistance [m] | 1.5 |
| Casting and coating | Yes |
| Max. rotation speed [deg/s] | 950 |
| Interface types | Digital |
| Interfaces | RS-422 |
| URL |
